> For the complete documentation index, see [llms.txt](https://help.qonic.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.qonic.com/documentation/qonic-application/modelling/creating/wall.md).

# Wall

Draw single walls or chains of connected walls, optionally with the layer structure of a wall component from your libraries.

Use the Wall tool to draw walls directly in your model. Pick a wall component from your component libraries and the new walls take its layer structure, snap to the model and connect to the walls around them.

{% embed url="<https://qonic.wistia.com/medias/9w2zqza290/>" %}

## Drawing Walls

1. In the toolbar, open the *BIM Creation* menu and click *Wall*, or use the <kbd>W</kbd> shortcut
2. (optional) Under **Structure**, choose a wall component. The list shows your component libraries first, then their components and variants; type to search all libraries at once. A component with a single variant is picked directly. Without a component, Qonic draws a generic single-layer wall that is 0.3 m thick
3. (optional) Set the **Height**. By default, Qonic detects it for you: it measures up to the slab, roof or covering above the walls you draw (between 1 and 10 m higher), and otherwise uses the height of the chosen component, or 2.5 m. A detected height is shown greyed out. Type a height to override it; clear the field or switch on *Auto height* to let Qonic detect it again
4. (optional) Choose how the walls are positioned on the line you draw. Under **Align on**, choose *Wall* to align the whole wall, or *Layer* to align one of its layers, and pick the **Alignment** (left, center or right). *Layer* is only available for components with more than one layer; choose the layer in the **Layer** field (the thickest layer is selected by default). Use *Flip* to swap the sides of a wall whose layers are not symmetrical
5. To draw a single wall, press and hold the left mouse button, move the cursor and release
6. To draw a chain of connected walls, click to place the first point and keep clicking to add segments. Click the last point again, or press <kbd>Enter</kbd>, to finish. Press <kbd>Esc</kbd> to discard the chain
7. (optional) While drawing a chain, type a length in the field and press <kbd>Enter</kbd> to lock the length of the current segment; then move the cursor to set its direction
8. (optional) To place walls along existing edges or [chalk curves](https://help.qonic.com/documentation/qonic-application/modelling/creating/line.md), select them while the tool is active

While you draw a chain, <kbd>Ctrl</kbd> <kbd>Z</kbd> takes back the last segment, and <kbd>Ctrl</kbd> <kbd>Y</kbd> puts it back.

The tool stays active after you finish, so you can keep drawing. The structure, height and alignment you chose carry over to the next chain.

New walls are connected automatically to each other and to the existing walls they meet. While drawing, the cursor snaps in the same way as in the [Line](https://help.qonic.com/documentation/qonic-application/modelling/creating/line.md) tool, and also to [grid](https://help.qonic.com/documentation/qonic-application/basics/visualisation-settings/grids.md) lines and to the axes of nearby walls and their extensions.

## Editing Walls

With the Wall tool active, click an existing wall to edit the whole chain it belongs to, or <kbd>Ctrl</kbd>+click it to edit only that wall. Then:

* Drag an end point to move it, or drag the midpoint to bend the wall into an arc
* Click an end point to continue the chain from it
* Drag from the wall to add a segment
* Change the **Structure** or the alignment to apply it to the walls you are editing

Press <kbd>Enter</kbd> to apply your changes, or <kbd>Esc</kbd> to discard them. Edited walls keep their own height. A wall whose path does not change keeps its geometry and openings, and only gets its layers replaced; when Qonic has to rebuild a wall, its windows, doors and openings are moved to the new wall.

{% hint style="info" %}
Walls drawn with a wall component are linked to it as adaptive instances: they follow the component's layer structure, but keep their own path, length, height and openings. See [Wall Components](https://help.qonic.com/documentation/qonic-application/modelling/components-panel.md#wall-components).
{% endhint %}
