> For the complete documentation index, see [llms.txt](https://help.qonic.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.qonic.com/documentation/qonic-application/modelling/snapping.md).

# Snapping

Snap to other geometry during modeling operations

To enable or disable snapping, use the Snapping toggle in the bottom toolbar or use the shortcut <kbd>Ctrl</kbd> +<kbd>Shift</kbd> + <kbd>S</kbd>. This turns all snapping on or off.

Qonic supports three types of snapping during modeling operations.

* Picking of a point on a surface or an edge, for example when selecting a starting point when creating new geometry. Supported snap points are vertices, edges and edge midpoints of existing geometry, chalk curves, centers of circles and arcs, cylinder axis endpoints, grid lines (when grids are shown), extension lines and the sketch grid. When the *Sketch Grid* is turned on in the bottom toolbar, points snap to the grid; see the [User Interface Overview](https://help.qonic.com/documentation/qonic-application/basics/user-interface-overview.md). The manipulator handle will be highlighted in blue to indicate it is snapping to something. Extension lines of existing edges will be highlighted in purple. The manipulator will display a grey disc to indicate the active plane.

<figure><img src="https://929210962-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FZKeCFTBZzqUt4lpmhUdS%2Fuploads%2FMqzdFgbayFIOAdC5hkUh%2FSnapping%20type%201.gif?alt=media&amp;token=6a11feb4-c124-4075-ae56-3994b83d8503" alt=""><figcaption></figcaption></figure>

* Picking a plane when doing a modeling operation along one axis, for example when push/pulling a face or moving a body in a given direction. Supported snap targets are surfaces parallel to the selected face, or clusters of vertices, edges, edge midpoints, chalk curves and/or cylinder axes in a plane parallel to the selected face. Grid planes and the origin planes (X, Y, Z) of the active model are also snap targets. The selected face will be highlighted in green, and the active snap target(s) will be highlighted in blue for clear visual feedback about what you are aligning the selected face with.\
  Note that the calculation of the possible snap targets per modeling operation happens in the background and can sometimes take a few seconds. This means on larger models, the snapping will only kick in after these calculations are done. Only objects in the current view are taken into account; if you orbit or zoom, the snap targets are recalculated. Mesh objects don't provide plane snap targets.\
  Also note that in larger models, there may be an 'overwhelming' number of possible snap targets depending on the operation you are doing. Therefore snap targets are ranked and filtered on relevance, based on factors such as

  * Scale - larger objects are more likely to be relevant than smaller objects,
  * Proximity to the manipulator - targets close to the current position are preferred,
  * Proximity to the camera - closer objects will likely be more relevant.

  If you want to align with a specific surface, but the surface doesn't show up as snap target - either because the calculation hasn't finished yet or because it was filtered out because of the above factors - you can still override this by hovering your cursor over the surface for a moment until it is highlighted in blue (press <kbd>Tab</kbd> to cycle through overlapping faces). Left-clicking the highlighted face will pick that face as the new snap target.\
  When nothing is snapped, distances are rounded to 1 mm (0.001 ft, or 1/16" for feet and fractional inches).

<figure><img src="https://929210962-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FZKeCFTBZzqUt4lpmhUdS%2Fuploads%2FQAcW9mP7EoWHmxFQ4eyb%2FSnapping%20type%202.gif?alt=media&amp;token=e018e14c-3cb2-4b56-9755-ce1708fdc2c8" alt=""><figcaption></figcaption></figure>

* Rotational snapping when rotating products or faces with the Transform tool: when a face of the rotated object comes within 10° of being parallel or perpendicular to a face of a nearby object, the rotation snaps to it. You can also hover over a face and click it to snap to it.

When inserting, moving or pasting components with reference geometry, use *Smart snapping* to align them automatically with walls, slabs and roofs. Read more in the article on [Components](https://help.qonic.com/documentation/qonic-application/modelling/components-panel.md#placing-components).

{% embed url="<https://qonic.wistia.com/medias/hxfjwpx7fb/>" %}
